Substances of very high concern (SVHC) analysis

Determination of selected volatile organic compounds (VOC) in water using the GC-MS and GC-FID techniques. Analysis can be conducted according to the following standard methods: EPA 624, EPA 5021A, EPA 8260, EPA 8015, EN ISO 10301, ISO 11423-1, and EN ISO 15680 The results of the analysis are reported in µg/L. Analysis includes the following analytes: Analyte: Reporting limits: chloromethane 1 µg/l bromomethane 1 µg/l dichloromethane 0.1 µg/l dibromimetaani 1 µg/l bromochloromethane 2 µg/l trichloromethane (chloroform) 0.1 µg/l tribromomethane (bromoform) 0.2 µg/l bromodichloromethane 0.1 µg/l dibromochloromethane 0.1 µg/l sum 4 trihalometanit 0.5 µg/l tetrachloromethane 0.1 µg/l trichlorofluoromethane 1 µg/l dichlorodifluoromethane 1 µg/l monochloroethane 1 µg/l 1,1-dichloroethane 0.1 µg/l 1,2-dichloroethane 0.1 µg/l 1,2-dibromietaani 0.5 µg/l 1,1,1-trichloroethane 0.1 µg/l 1,1,2-trichloroethane 0.1 µg/l 1,1,1,2-tetrachloroethane 0.1 µg/l 1,1,2,2-tetrachloroethane 1 µg/l vinyl chloride 0.1 µg/l 1,1-dichloroethene 0.1 µg/l cis-1,2-dichloroethene 0.1 µg/l trans-1,2-dichloroethene 0.1 µg/l amount of 1,2-dichloroethene 0.2 µg/l trichloroethylene 0.1 µg/l sum of 11 chlorinated hydrocarbons 1.1 µg/l tetrachloroethene 0.1 µg/l Sum of trichloroethylene and tetrachloroethylene 0.2 µg/l sum 5 chlorinated ethylenes 0.5 µg/l 1,2-dichloropropane 1 µg/l 1,3-dichloropropane 1 µg/l 2,2-dichloropropane 1 µg/l 1,2,3-trichloropropane 1 µg/l 1,2-dibromo-3-chloropropane 1 µg/l 1,1-dichloro-1-propene 1 µg/l cis-1,3-dichloro-1-propene 1 µg/l trans-1,3-dichloropropene 1 µg/l hexachlorobutadiene 1 µg/l 2-chlorotoluene 1 µg/l 4-chlorotoluene 1 µg/l monochlorobenzene 0.1 µg/l bromobenzene 1 µg/l 1,2-dichlorobenzene 0.1 µg/l 1,3-dichlorobenzene 0.1 µg/l 1,4-dichlorobenzene 0.1 µg/l amount of 3 dichlorobenzene 0.3 µg/l 1,2,3-trichlorobenzene 0.1 µg/l 1,2,4- trichlorobenzene 0.1 µg/l 1,3,5-trichlorobenzene 0.1 µg/l amount of 3 trichlorobenzene 0.4 µg/l benzene 0.1 µg/l toluene 0.5 µg/l ethylbenzene 0.1 µg/l o-xylene 0.1 µg/l m/p-xylene 0.2 µg/l sum of xylenes 0.3 µg/l summa BTEX 1 µg/l board one 0.2 µg/l isopropylbenzene 1 µg/l n-propylbenzene 1 µg/l 1,2,4-trimethylbenzene 1 µg/l 1,3,5-trimethylbenzene 1 µg/l n-butylbenzene 1 µg/l sec-butylbenzene 1 µg/l tert-butylbenzene 1 µg/l p-isopropyltoluene 1 µg/l naphthalene 1 µg/l Diisopropyl ether (DIPE) 0.6 µg/l ETBE (ethyl tert-butyl ether) 0.2 µg/l MTBE (methyl tert-butyl ether) 0.2 µg/l tert-amyl ethyl ether (TAEE) 0.2 µg/l TAME 0.2 µg/l tert-butyl alcohol (TBA) 5 µg/l ethanol 100 µg/l A customized offer can also be prepared if you are interested in analyzing only individual compounds from a sample. Suitable sample containers for analysis can be ordered through us. Sample containers picked up from Measurlabs are included in the price of the analysis, but sample containers can also be shipped to the customer for a separate fee.

Determination of total fluorine (F) content in plastic according to the EN 15408 mod. method. The fluorine content of the sample is obtained using oxygen bomb combustion treatment followed by ion chromatography (IC). Possible sample preparation, such as grinding into smaller particles, is available at an extra cost. This method can also be used to determine the total content of S, Cl, and Br. The results will be reported in mg/kg.

The following analyses are included in this nanoparticle analysis package, intended to characterize nanoforms according to the REACH Regulation. Particle size distribution and aspect ratios by SEM-EDX Preparation with isopropanol, Sample dispersion on a slide, with centrifugation, SEM analysis and particle count by image analysis, Nanoparticle detection and classification according to the 2022 EC recommendation on the definition of nanomaterial, Reporting of PSD parameters for ~300 particles, including the following: PSD diagram, accumulated and individual., Feret min (min, d10, d25, d50, d75, d90, d95, max), Feret max (min, d10, d25, d50, d75, d90, d95, max), Equivalent circular diameter (min, d10, d25, d50, d75, d90, d95, max), Aspect ratio (calculated based on individual Feret min and Feret max measurements), Number based nano-fraction (%).. Crystal phase analysis by XRD/Rietveld method Sample preparation: drying, grinding, X-ray preparation, XRD analysis over an angular range extending from 10° to 90°, Identification of the crystalline phases present in the sample, Semi-quantitative analysis of phase distribution, using the Rietveld method, Interpretation of diffractograms. Chemical composition/purity by ICP-AES and CHNS analysis ICP-AES quantification of inorganic and metallic elements: Ag, Al, As, B, Ba, Be, Bi, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Ni, P, Pb, S, Se, Sb, Si, Sn, Sr, V, Zn, Ti, and Tl, Determination of C, H, N, and S with an elemental analyzer. Volume-specific surface area (VSSA) and VSSA diameter calculations (optional) BET specific surface area measurement of powder by nitrogen adsorption, True (skeletal) density measurement by He pycnometry, excluding intergranular and intragranular porosity, Both analyses include sample preparation. You can request a quote for the analysis using the form below. Please note that the OECD 125 guideline does not apply to this analysis.

GC-MS analysis of 16 PAH compounds, which are listed as high-priority pollutants by the U.S. Environmental Protection Agency (EPA). The analyzed PAH compounds are: naphthalene [CAS: 91-20-3], acenaphthylene [CAS: 208-96-8], acenaphthene [CAS: 83-32-9], fluorene [CAS: 86-73-7], phenanthrene [CAS: 85-01-8], anthracene [CAS: 120-12-7], fluoranthene [CAS: 206-44-0], pyrene [CAS: 129-00-0], benz(a)anthracene [CAS: 56-55-3], chrysene [CAS: 218-01-9], benzo(b)fluoranthene [CAS: 205-99-2], benzo(k)fluoranthene [CAS: 207-08-9], benzo (a) pyrene [CAS: 50-32-8], dibenzo(ah)anthracene [CAS: 53-70-3], benzo (ghi) perylene [CAS: 191-24-2], indeno (123cd) pyrene [CAS: 193-39-5].

The purpose of cleaning validation studies is to show that reusable medical devices can be reprocessed effectively between uses so that patients are not exposed to pathogens. Depending on the device’s intended use and classification, appropriate reprocessing steps may include cleaning, disinfection, and/or sterilization. For cleaning validation more specifically, the testing procedure consists of three steps: Simulated contamination with artificial soils that accurately reflect clinically relevant soils, such as blood and other bodily fluids. , Cleaning (manual and/or automated), carefully following the manufacturer's instructions for parameters such as detergents, cleaning tools, water quality, and temperature. , Inspection, both visually and using quantitative methods relevant to the test soil (e.g., proteins, total organic carbon, or hemoglobin), to assess whether residual contaminants remain on the device.. Successful cleaning validation is often sufficient for non-critical reusable devices, such as blood pressure cuffs, monitors, and clutches. Semi-critical and critical devices will require further disinfection and/or sterilization validation studies, which we can also offer. The displayed example price covers a manual cleaning validation study with 6 reprocessing cycles and cleanability evaluations with visual inspection & protein content measurement. Test protocol formulation and reporting are also included.

The burning rate of horizontally mounted materials designed to be used in vehicles and buses must be tested with the UN/ECE R118 annex 6 test before they can be approved for use. Measurlabs offers this and the other R118 tests with accreditation. In the test method, the exposed side of the test specimen is burned from underneath and the burning rate is measured and expressed in mm/min.

BET (Brunauer–Emmett–Teller) analysis to determine the specific surface area of solid materials.

The melting behavior of fusible materials used in certain motor vehicles must be determined according to Annex 7 of UN/ECE Regulation 118. In the test, it is monitored whether the specimen ignites, creates flaming droplets, and if these droplets ignite cotton wool placed under the specimen. For the material to pass the test, there must be no formation of flaming drops that ignite the cotton wool. Measurlabs can offer accredited test reports for the UN/ECE R118 Annex 7 test, as well as the Annex 6 and Annex 8 tests. Non-isotropic materials must be tested from both sides, which means that double the number of samples is required.

Rutherford Backscattering Spectrometry (RBS) can be used to measure the composition of solid samples quantitatively at the surface as well as depth profiling. RBS is used for the analysis of heavy elements and can be combined with ToF-ERDA when lighter elements also need to be analyzed. Elements with similar mass can be difficult to differentiate.

Analysis package for mycotoxins listed in Commission Regulation (EU) No 2023/915, including the following determinations: Aflatoxin B1, B2, G1, G2, Ochratoxin A, T-2, HT-2 toxins, Deoxynivalenol, Zearalenone. Testing of the listed mycotoxins is usually required for almost all types of cereals and cereal products, including foods for infants and young children. We can also offer additional mycotoxin analyses, including for ergot alkaloids and patulin. Do not hesitate to ask for more information or request a quote.